Architectural Railing Systems

Termination Stud System

Attachment: Our Termination Stud System is very simple to setup and install. Simply drill holes in your verticals for the cable to pass through. The termination cap pulls against the last vertical to tension.

Examples of Applications: This system is very good for retrofitting existing rails to meet current codes. Termination Studs are a very cost effective and clean method of installing and tensioning cable assemblies because they can be used with any type or style of post. The termination shaft on the turnbuckle is available in different lengths to pass through various post sizes.

Other Information: Our standard termination stud turnbuckle can be used for up to a 2" OD post on a level or angle run. Rods are also available for 6", and 12" posts.
(316 grade stainless steel).

Termination Stud
Cap Size (a) Wire Size (c) Part #
9/16" 1/8" TS3
9/16" 5/32" TS4
9/16" 3/16" TS5
3/4" 1/4" TS6
9/16" 1/4" TS61
Add any of these end fittings to our threaded stud system hardware.
Handy Crimp Termination Stud
Cap Size (a) Wire Size (c) Part #
9/16" 1/8" TS3C
9/16" 1/8" TS5C
Termination Stud Turnbuckles
Wire Size
(c)
Thread
(b)
Body L
(d)
Open L
(e)
Closed L
(e)
Cap Size
(a)
Part #
1/8" 1/4-28 4-1/4" 10-1/4" 7-1/8" 9/16" 6TT3TS
5/32" 1/4-28 4-1/4" 10-1/2" 7-1/2" 9/16" 6TT4TS
3/16" 1/4-28 4-1/4" 10-1/2" 7-1/2" 9/16" 6TT5TS
3/16" 5/16-24 4-3/4" 10-3/4" 8" 9/16" 8TT5TS
1/4" 5/16-24 4-3/4" 10-3/4" 8-1/8" 3/4" 8TT6TS
1/4" 5/16-24 4-3/4" 10-3/4" 8-1/8" 9/16" 10TT6TS
Handy Crimp Termination Stud Turnbuckles
Wire Size
(c)
Thread
(b)
Body L
(d)
Open L
(e)
Closed L
(e)
Cap Size
(a)
Part #
1/8" 1/4-28 4-1/4" 10-1/4" 7-1/8" 1/4" 6TT3TSC
3/16" 1/4-28 4-1/4" 10-1/2" 7-1/2" 1/4" 6TT4TSC

Countersunk Termination Stud System

Our countersunk termination stud system utilizes the same features as our termination stud system with a flush fit look. To be used with flat bar or box tube posts. Simply use a standard 82° countersink on your end posts and the fitting will fit flush.

Countersunk Termination Studs
Cap Size
(a)
Wire Size
(c)
Part #
9/16" 1/8" CTS3
9/16" 5/32" CTS4
9/16" 3/16" CTS5
Handy Crimp
Countersunk Termination Studs
Cap Size
(a)
Wire Size
(c)
Part #
9/16" 1/8" CTS3C
9/16" 3/16" CTS5C
Countersunk Termination Stud Turnbuckles
Wire Size
(c)
Thread
(b)
Body L
(d)
Open L
(e)
Closed L
(e)
Cap Size
(a)
Part #
1/8" 1/4-28 4-1/4" 11" 8" 9/16"
6TT3CTS
5/32" 1/4-28 4-1/4" 11-1/8" 8-1/8" 9/16"
6TT4CTS
3/16" 1/4-28 4-1/4" 11-1/4" 8-1/4" 9/16"
6TT5CTS
Handy Crimp Countersunk Termination Stud Turnbuckles
Wire Size
(c)
Thread
(b)
Body L
(d)
Open L
(e)
Closed L
(e)
Cap Size
(a)
Part #
1/8" 1/4-28 4-1/4" 11" 8" 1/4"
6TT3CTSC
3/16" 1/4-28 4-1/4" 11-1/4" 8-1/8" 1/4"
6TT5CTSC

Swage to Swage Turnbuckles

For longer cable runs or simply to establish a certain look, swage to swage cables can be used. Swage to swage turnbuckles can be used in the middle of or anywhere along a cable run for look as well as functionality. They can be used to extend a cable run to any length by spacing them along the cable approximately 25 to 35 apart. Swage to swage turnbuckles can be used in combination with any termination style fittings and are 316 grade stainless steel.

Swage to Swage Turnbuckles
Wire Size
(c)
Thread
(b)
Body L
(d)
Open L
(e)
Closed L
(e)
Part #
1/8" 10-32 3-1/2" 6-1/2" 4-1/2" 5TT3SS
1/8" 1/4-28 4-1/4" 8" 5" 6TT3SS
5/32" 1/4-28 4-1/4" 10-1/2" 7-1/2" 6TT4SS
3/16" 1/4-28 4-1/4" 10-1/2" 7-1/2" 6TT5SS
3/16" 5/16-24 4-3/4" 10-3/4" 8" 8TT5SS
1/4" 5/16-24 4-3/4" 10-3/4" 8-1/8" 8TT6SS
1/4" 5/16-24 4-3/4" 10-3/4" 8-1/8" 10TT6SS
Handy Crimp Termination Stud Turnbuckles
Wire Size
(c)
Thread
(b)
Body L
(d)
Open L
(e)
Closed L
(e)
Part #
1/8" 1/4-28 4-1/4" 8" 5" 6TT3TSC
3/16" 1/4-28 4-1/4" 8-1/4" 5-1/2" 6TT4TSC

Adjust-A-Balls

Adjust-A-Balls are used for stair angle compensation. These half round balls allow for the cable to swivel to the proper stair angle automatically. Simply drill the proper hole and the ball will adjust to the proper position as the cable is tensioned.

Adjust-A-Balls
Ball Size
(s)
Hole Size
(t)
Part #
3/4" 25/64" AJB

Toggle Jaw System

Attachment: Features fork style ends for attachment with screws and nuts (supplied) for a variety of post styles including: tee-stock, angle iron, flat bar welded to post, loops attached to post, eyebolts (shown below), etc. The toggling feature allows for angled takeoff.

Examples of applications:
cable rails, hanging signs or shelving, even structural applications such as canopy supports, collar tie cables, or fabric structures.

Other Information: Attachment size corresponds to width of clevis, ex. 1/4" pin=1/4" opening. Toggles come supplied with cotter pin and ring pins, or screws and lock nuts. Toggle jaws may also be combined with any other system. (316 grade stainless steel). Fixed fork hardware is used for cable sizes 1/2" through 1". Fixed fork clevis hardware is also available for smaller sizes as a special order.

Toggle Jaws
Screw Size
(l)
Jaw Width
(k)
Wire Size
(c)
Part #
3/16" 1/4" 1/8" 5TJ3
1/4" 1/4" 1/8" 6TJ3
1/4" 1/4" 5/32" 6TJ4
1/4" 1/4" 3/16" 6TJ5
5/16" 5/16" 3/16" 8TJ5
5/16" 5/16" 1/4" 8TJ6
3/8" 3/8" 1/4" 10TJ6
Handy Crimp Toggle Jaws
Screw Size
(l)
Jaw Width
(k)
Wire Size
(c)
Part #
1/4" 1/4" 1/8" 6TJ3C
1/4" 1/4" 3/16" 6TJ5C
Toggle Jaw Turnbuckles
Wire Size
(c)
Thread
(b)
Body L
(d)
Open L
(e)
Closed L
(e)
Screw Size
(l)
Jaw Width
(k)
Part #
1/8" 10-32 3-1/2" 7-5/8" 5-1/4" 3/16" 1/4"
5TT3JS
1/8" 1/4-28 4-1/4" 9" 6-5/8" 1/4" 1/4"
6TT3JS
5/32" 1/4-28 4-1/4" 9-1/8" 6-5/8" 1/4" 1/4"
6TT4JS
3/16" 1/4-28 4-1/4" 9-3/8" 6-5/8" 1/4" 1/4" 6TT5JS
3/16" 5/16-24 4-3/4" 10-1/4" 7-1/2" 5/16" 5/16" 8TT5JS
1/4" 5/16-24 4-3/4" 10-1/2" 7-5/8" 5/16" 5/16" 8TT6JS
1/4" 3/8-24 5-1/4" 11-3/8" 8-1/4" 3/8" 3/8" 10TT6JS
Toggle Jaw Turnbuckles
Wire Size
(c)
Thread
(b)
Body L
(d)
Open L
(e)
Closed L
(e)
Screw Size
(l)
Jaw Width
(k)
Part #
1/8" 1/4-28 4-1/4" 9" 6-5/8" 1/4" 1/4"
6TT3JSC
3/16" 1/4-28 4-1/4" 9-3/8" 6-5/8" 1/4" 1/4"
6TT5JSC
Eye Bolts
Shank L
(v)
Thread L
(w)
Thread Size
(u)
Part #
1" 7/8" 1/4-20 EB6S
1-7/8" 1-3/4" 1/4-20 EB6M
3" 2-3/4" 1/4-20 EB6L
1-7/8" 1-3/4" 5/16-18 EB8S
4-1/2" 3" 5/16-18 EB8M
2-1/2" 2-3/8" 3/8-16 EB10S
4-1/4" 3" 3/8-16 EB10M
Eye Lags
Shank L
(x)
Thread L
(y)
Thread Size
(z)
Part #
2-3/4" 1-3/4" 1/4" LEB6
2-3/4" 1-3/4" 5/16" LEB8
2-3/4" 1-3/4" 3/8" LEB10

Deck Toggle System

Attachment: is by two screw holes in the deck toggle base. Deck toggles are excellent for attaching to wood posts or blocking (requires minimum 3" wood blocking). Please note that the cable strength is based on the attachment screws and the attachment material.

Examples of Applications: Our Deck Toggle System is used for cables that need to be face mounted or where an angled takeoff is required. These toggles can be used with any post configuration and are excellent for angled cable runs as our deck toggle fittings articulate more than 90 degrees.

Other Information:
Deck toggles can be attached to either side of a common post by through bolting or if wall thickness of post is thick enough you can drill and tap posts to accept machine screws. Components can be mixed and matched with other systems for versatility. 316 grade stainless steel for superior corrosion resistance.

Deck Toggles
Wire Size
(c)
Screw Size
(l)
Hole Spacing
(k)
Part #
1/8" 1/4" 1-1/2"
6TJ3DT
5/32" 1/4" 1-1/2" 6TJ4DT
3/16" 1/4" 1-1/2" 6TJ5DT
3/16" 5/16" 1-3/4" 8TJ5DT
1/4" 5/16" 1-3/4" 8TJ6DT
1/4" 3/8" 2" 10TJ6DT
Handy Crimp Deck Toggles
Wire Size
(c)
Screw Size
(l)
Hole Spacing
(k)
Part #
1/8" 1/4" 1-1/2"
6TJ3DT
3/16" 1/4" 1-1/2" 6TJ5DT

Deck Toggle Turnbuckles
Wire Size
(c)
Thread
(b)
Body L
(d)
Open L
(e)
Closed L
(e)
Screw Size
(l)
Hole Spacing
(k)
Part #
1/8" 1/4-28 4-1/4" 9" 6" 1/4" 1-1/2"
6TT3DT
5/32" 1/4-28 4-1/4" 9-1/4" 6-1/4" 1/4" 1-1/2"
6TT4DT
3/16" 1/4-28 4-1/4" 9-1/4" 6-1/4" 1/4" 1-1/2"
6TT5DT
3/16" 5/16-24 4-3/4" 9-3/4" 6-3/4" 5/16" 1-3/4" 8TT5DT
1/4" 5/16-24 4-3/4" 9-3/4" 6-3/4" 5/16" 1-3/4" 8TT6DT
1/4" 3/8-24 5-1/4" 10-3/4" 7-3/4" 3/8" 2" 10TT6DT
Deck Toggle Turnbuckles
Wire Size
(c)
Thread
(b)
Body L
(d)
Open L
(e)
Closed L
(e)
Screw Size
(l)
Hole Spacing
(k)
Part #
1/8" 1/4-28 4-1/4" 8" 6" 1/4" 1-1/2"
6TT3DTC
3/16" 1/4-28 4-1/4" 9-1/8" 6-1/4" 1/4" 1-1/2"
6TT4DTC

Lag Screws

Screw Size Part #
1/4" x 1/2" SL6S
1/4" x 2-1/2" SL6L
5/16" x 1-1/2" SL8S
5/16" x 2-1/2" SL8L
3/8" x 1-1/2" SL10S
3/8" x 2-1/2" SL10L

Lag Turnbuckle System

Attachment: Pre-drill your holes to minimum size necessary. Different woods require different hole sizes. Use of a lubricant such as soap or wax will allow easier installation of lag into the post. Use caution not to use a material that will stain your posts. Our lag studs require a minimum of 3 inches of wood blocking

Examples of Applications: Our lag system is designed for direct attachment into wooden surfaces.

Other Information: Lag hardware should be fully engaged before tension is applied to cables. Since these cables are only as strong as the lag holding power and mounting material (solid wood blocking is required), they are only recommended for light duty use and not for commercial use. (316 grade stainless steel)

Lag Studs
Wire Size
(c)
Part #
1/8" LS3
5/32" LS4
3/16" LS5
Lag Studs
Wire Size
(c)
Part #
1/8" LS3C
3/16" LS5C
Lag Screw Turnbuckles
Wire Size
(c)
Thread
(b)
Body L
(d)
Open L
(e)
Closed L
(e)
Part #
1/8" 1/4-28 4-1/4" 8" 5"
6TT3L
5/32" 1/4-28 4-1/4" 8-1/4" 5-1/4"
6TT4L
3/16" 1/4-28 4-1/4" 8-1/4" 5-1/4"
6TT5L
3/16" 5/16-24 4-3/4" 8-3/4" 5-3/4" 8TT5L
Handy Crimp Lag Screw Turnbuckles
Wire Size
(c)
Thread
(b)
Body L
(d)
Open L
(e)
Closed L
(e)
Part #
1/8" 1/4-28 4-1/4" 8" 5"
6TT3LC
3/16" 1/4-28 4-1/4" 8-1/4" 5-1/4"
6TT5LC

Threaded Termination Stud System

Attachment: Our Threaded Termination Stud System is very easy to setup and install. Simply drill holes in your verticals for the cable to pass through. Nuts and cap nuts pull against the last vertical to tension. Cables in this system are fabricated to allow the threaded studs to pass through to the outside of the end posts. You then secure and tension the cables by threading a stainless hex nut onto the stud. You tighten the hex nut against the outside of your end post until the cable is tensioned properly. End of stud will be capped off with a stainless acorn cap nut, dome nut, or ball end.

Examples of Applications:
Threaded termination studs can be a very clean and cost effective method of installing and tensioning cable assemblies. This system is very good for retrofitting existing rails to meet current codes. These can be used in conjunction with our termination stud system, using a termination stud on one end and a threaded stud on the other can support a run of up to 20 feet. Using a threaded stud on both ends will support a run of 30-40 feet.

Other Information: The threaded stud on the turnbuckle is available in different lengths to pass through various post sizes. Use with washers, and cap (acorn) nuts, ball ends, or dome nuts. 316 grade stainless steel for superior corrosion resistance.

Threaded Studs
Cap Size
(a)
Wire Size
(c)
Part #
1/4-28 1/8" 6S3
1/4-28 5/32" 6S4
1/4-28 3/16" 6S5
5/16-24 3/16" 8S5
5/16-24 1/4" 8S6
Add any of these end fittings to our threaded stud system hardware
Threaded Studs
Cap Size
(a)
Wire Size
(c)
Part #
1/4-28 1/8" 6S3C
1/4-28 3/16" 6S5C
Threaded Stud Turnbuckles
Wire Size
(c)
Thread
(b)
Body L
(d)
Open L
(e)
Closed L
(e)
Part #
1/8" 1/4-28 4-1/4" 10-1/4" 7-1/8"
6TT3S
5/32" 1/4-28 4-1/4" 10-1/2" 7-1/2"
6TT4S
3/16" 1/4-28 4-1/4" 10-1/2" 7-1/2"
6TT5S
3/16 5/16-24 4-3/4" 10-3/4" 8" 8TT5S
1/4" 5/16-24 4-3/4" 10-3/4" 8-1/8" 8TT6S
Handy Crimp Threaded Stud Turnbuckles
Wire Size
(c)
Thread
(b)
Body L
(d)
Open L
(e)
Closed L
(e)
Part #
1/8" 1/4-28 4-1/4" 10-1/4" 7-1/8"
6TT3SC
3/16" 1/4-28 4-1/4" 10-1/2" 7-1/2"
6TT5SC

Adjust-A-Balls

Adjust-a-balls are used for stair angle compensation. These half round balls allow for the cable to swivel to the proper stair angle automatically. Simply drill the proper hole and the ball will adjust to the proper position as the cable is tensioned.

Ball Size Hole Size Part #
3/4 25/64" AJB1

Replacement Hardware

These newly redesigned swage studs are now completely CNC machined for optimum quality and strength. Available in both handy crimp or machine swage. (316 grade stainless steel) New Hardware includes more end fittings for threaded studs such as ball ends and dome nuts. Also available are 30 degrees. beveled washers. If you don't see something here, call and ask.

Handy Crimp Swage Studs
Wire Size
(c)
Thread Size
(b)
Thread L
(p)
Part #
1/8" 1/4-28RH 7/16" 6S3CRS
1-1/2" 6S3CRM
2-1/4" 6S3CRL
3/16" 1/4-28RH 7/16" 6S5CRS
1-1/2" 6S5CRM
2-1/4" 6S5CRL
3/16" 5/16-24RH 7/16" 8S5CRS
1-1/2" 8S5CRM
2-1/4" 8S5CRL
Swage Studs (Machine Swage)
Cable Size
(c)
Thread Size
(t)
Thread L
(p)
Part #
1/8" 10-32 RH 3/8"
5S3RS
1-1/2" 5S3RM
1/8" 1/4-28 RH 7/16" 6S3RS
1-1/2" 6S3RM
2-1/4" 6S3RL
3-1/4" 6S3RX
5/32" 1/4-28 RH 7/16" 6S4RS
1-1/2" 6S4RS
2-1/4" 6S4RL
3-1/4" 6S5RX
3/16" 1/4-28 RH 7/16"
6S5RS
1-1/2" 6S5RS
2-1/4" 6S5RL
3-1/4" 6S5RX
3/16" 5/16-24 RH 7/16" 8S5RS
1-1/2" 8S5RM
2-3/8" 8S5RL
1/4" 5/16-24 RH 7/16" 8S6RS
1-1/2" 8S6RM
2-3/8" 8S6RL
1/4" 3/8-24 RH 7/16" 10S6RS
1-1/2" 10S6RM
2-3/4" 10S6RL
Bold indicates standard length used in turnbuckles of that wire size.

Washers

Thread Washers Fender Washers Lock Washers
1/4 14WAS 14FEN 14WASL
5/16 516WAS 516FEN 516WASL
3/8 38WAS 38FEN 38WASL
1/2 12WAS 12FEN 12WASL
5/8 58WAS - -
3/4 34WAS - -

Nuts

Thread Hex Nuts Lock Nuts
1/4-28 RH 14LNR 14LNF
LH 14LNL -
5/16 RH 516LNR 516LNF
LH 516LNL -
3/8-24 RH 38LNR 38LNF
LH 38LNL -
1/2-20 RH 12LNR -
LH 12LNL -
5/8-18 RH 58LNR -
LH 58LNL -
3/4-10 RH 34LNR -
LH 34LNL -

End Caps

Thread Cap Nut Ball Ends Dome Nuts
1/4-28 RH CAP6 BALL6 DN6
5/16-24 RH CAP8 BALL8 -
3/8 RH CAP10 - -

Beveled Washers

Thread Size Beveled Washer
1/4-28 BW5
5/16-24 BW6

© VER SALES, INC. 2011
All Rights Reserved
.